|
|
|
|
|
| Coulombuster Series | ||||
| Model | NK-100/1002 | NK-3001 | NK-5001 | NK-7001 |
| Detection Method | Capacitor-charging | Vibration-type surface potential sensor | Vibration-type surface potential sensor | Vibration-type surface potential sensor |
| Display | Digital LCD | Digital LCD | Digital LCD | Digital LCD |
| Charge plate | - | - | - | Stainless steel, 20 x 38mm |
| ES capacitance | - | - | - | 10 pF (±2pF) |
| Decay characteristics | - | - | - | 1)
Time from 1000V to 100V 2) Time from 200V to 20V |
| Measurement range |
±0.01-99.99 nC (NK-1001) ±1-9999 nC (NK-1002) |
±0.1-999.9V | ±0.01-999.9V | ±0.01-±1999.9V 0.01-99.99 sec (decay time) |
| Environment |
- |
0-40°C, 65% or lower RH |
- |
0-40oC, 65% or lower RH |
| Measurement accuracy | Within ±5% | Within ±5% | Within ±5% | Within ±5% |
| Power supply | 2 AAA alkaline dry cell batteries (provides 4 or more hours continuous use) | 2 AAA alkaline dry cell batteries (provides 4 or more hours continuous use) | 2 AAA alkaline dry cell batteries (provides 4 or more hours continuous use) | 4AAA
alkaline dry cell batteries AC 100V |
| Options |
Conductive probe tip AC adapter Recording device connector cables |
AC adapter Recording device connector cables |
AC adapter Recording device connector cables |
- |
| Model 7000 (ESD & Latch-up Tester) | ||
| ESD simulation | ||
| Pin selection method | ||
| . | Types E, EL: | automated 2-axis robot and relay matrix |
| High voltage (HV) | ||
| . | Type E, EL: Type L: |
±1000/4500/8000
V, 1% ±5V ±1000, 1% ±5V |
| DC measurement | ||
| Vcc1 | Power supply | (combined DC/pulsed) |
| . | Voltage: | ±30 V/ 50 mV increments |
| Current: |
±500 mA/100mA minimum resolution (ESD test time) ±100 mA/1mA minimum resolution (LUP test time) |
|
| Vcc2-4 (DC power) | ||
| Voltage: | ±15 V/ 50 mV increments | |
| . | Current: | same as Vcc1 |
| VF/IM (Voltage force and current measurement | ||
| . | Voltage: | ±15 V/ 10 mV increments |
| Current: | ±100 mA/ 10mA minimum resolution | |
| DVM | (digital volt meter) | |
| Voltage: | ±30 V/ 10 mV increments | |
| ip | (current pulse) | generator |
| Voltage: | ±30 V/ 50 mV minimum resolution | |
| . | Current: | ±100 mA/1mA increments |
| vp | (voltage pulse) | generator |
| . | voltage: | ±30V/ 50mV minimum increments |
| DUT stabilization | ||
| Pull-up (PU), pull-down (PD) | ||
| . | Vcc1-4 via 1-K Ohm, Max Hr/Min L, connected to ground, etc. | |
| DUT connection: | Automatic | |
| Multi-channel/Control power supply (VCTL) | ||
| No. of channels: | 4 | |
| 4-channel clock generator (4CH CLK) | ||
| Period, frequency: | Channel 1 10 k/100k/Mhz selectable | |
| . | Channel 2 Invert of Channel 1 | |
| Channel 3 1µs-100 µs/1 µs increments | ||
| . | Channel 4 Invert of Channel 3 | |
| 16-channel pattern generator (16CH PTN) | ||
| . | No. of channels: | 1
clock channel 16 pattern channels |
| clock: | 1 µs-1001 µs/11 µsincrements | |
| Dimensions/ AC input, etc. | ||
| Main body (mm) | 1100(W) x 900(H) x 800(D) | |
| Weight | Less than 200kg | |
| AC power | 100
V ±10% 50/60 Hz Single phase, less than 1.5 kVA |
|
| Temperature | 10-40°C | |
| ECDM-100E/400E Simulator | ||||
| Zapping voltage | 0-±100
V/1000 V Ecdm-100E 0-±400 V/4000 V Ecdm-400E |
|||
| High voltage display | Voltage settings vary according to digital display monitor | |||
| Voltage settings | Digital
panel meter/potentiometer Low/High voltage range switching Minimum resolution: 0.1 V (Ecdm-100E), 1 V for others |
|||
| Polarity | Positive-negative-off 3-way selectable switch | |||
| Repetition | 1-99 or continuous thumb wheel switch | |||
| Output enabler | Push-button switch | |||
| Wristband terminal | Available | |||
| AC power supply | 85-132 V or 170-264 V, 50/60 Hz, 20 VA (selectable) | |||
| External
weight/dimensions (mm) (approx.) |
Main body: 7
kg/ 257(W) x 145(H) x 362(D) Probe: 25(W) x 148(L) x 17(D) |
|||
| Options | ||||
| Probe types | ||||
| 1) HBM | Model E-3H | (ESDA and JEDEC standards) | ||
| . | 2) MM | Model E-7M | (ESDA and JEDEC standards) | |
| 3) CDM | Model P-3A | (charged tool model) | ||
| . | 4) CPM | Model P-4F | . | |
| 5) TLP Model T-4N | (medium rise), | T-4F (fast rise) | ||
| Jigs/Miscellaneous | ||||
| 1) Fixed probe stand | Model ICJ-1 | |||
| . | 2) X-Y derectional | Model TST-1 | . | |
| 3) DUT jig | ||||
| . | 4) Probe pins 0.3, 0.5, 1.0 mm and other diameters | |||
| Copyright 2001 Uniglobe Kisco, Inc. All rights reserved. | ||||